|
| Author | Message |
|---|
DamonFB
FBHQ Beginner
Posts : 65
Join date : 2011-09-01
Setup : FlatFace G12 with TD wides and china bearing wheels
 |  Subject: Re-lacquering? Fri Nov 25, 2011 1:45 am | |
| Hey guys, I was wondering if it is possible to re-lacquer a deck as mine is getting some wear on it. I wasn't sure, and i'm concerned about lacquering over the holes and was just wondering if anybody does it or what i should do. Thanks!  |
|
| | |
Trop32
FBHQ Regular
Posts : 734
Join date : 2011-09-18
Age : 26
Location : K-Town Vermont
Companies : Snowboarding, Skateboarding, Fingerboarding
Setup : Jack shit.
| | Subject: Re: Re-lacquering? Fri Nov 25, 2011 1:48 am | |
| My friend recently did it he just took some news paper slabbed his deck on their and sprayed turned out good but he forgot to cover the grip so that got some on it and dried now it is hard so try to cover tape  |
|
| | |
Danny H
Admin
Posts : 10438
Join date : 2009-07-13
Age : 28
Location : Leeds
Setup : Blosom Split Ply
TNP Tape
Y-Trucks X4
Cartwheels
| | Subject: Re: Re-lacquering? Fri Nov 25, 2011 7:37 am | |
| ^Or take it off, and laquer the whole deck? |
|
| | |
DamonFB
FBHQ Beginner
Posts : 65
Join date : 2011-09-01
Setup : FlatFace G12 with TD wides and china bearing wheels
| | Subject: Re: Re-lacquering? Fri Nov 25, 2011 8:24 am | |
| what about the truck holes and kingpin holes? won't the lacquer cover them over? should i do it with just the base plate on or something? |
|
| | |
TributeDecks
FBHQ Beginner
Posts : 11
Join date : 2011-11-15
Age : 34
| | Subject: Re: Re-lacquering? Fri Nov 25, 2011 9:30 am | |
| Damon, look your holes and kingpins will be fine, just lacquer over them and don't worry about them. Just make sure that after you refinish your board to take a 1/16th inch drillbit and 1/8th drill bit to your holes.
Basically all your doing with the drillbits is removing all the excess clearcoat. use the 1/16th for the holes themselves and the 1/8th for the countersinks and kingpins.
I don't suggest using the drill with it though. The best/safest method to do it would be to just turn/twist the drillbits with your hands to make sure you don't fuck up the holes. Also when doing the countersinks/kinpins don't push down when you do em cause you might make them deeper. Just very lightly turn it between your fingers so that it just takes the top part of the wood/clearcoat off. |
|
| | |
DamonFB
FBHQ Beginner
Posts : 65
Join date : 2011-09-01
Setup : FlatFace G12 with TD wides and china bearing wheels
| | Subject: Re: Re-lacquering? Fri Nov 25, 2011 10:39 am | |
| okay, thank you |
|
| | |
Alex.
FBHQ Regular
Posts : 541
Join date : 2010-11-22
| | Subject: Re: Re-lacquering? Fri Nov 25, 2011 12:04 pm | |
| You could leave screws in the holes whilst you do it. I wouldn't worry about it though if you're using spray lacquer, you shouldn't have any problems. If you do, do what Piller said. Don't re-drill them though... it's unnecessary and you might mess them up. |
|
| | |
WillSteller
Constant FBHQer
Posts : 1080
Join date : 2011-07-03
Age : 27
Location : Vermont
Companies : Snowboarding, Skating
Setup : Emanant
NoLogo
FF
FBS
| | Subject: Re: Re-lacquering? Fri Nov 25, 2011 1:28 pm | |
| - Trop32 wrote:
- My friend recently did it he just took some news paper slabbed his deck on their and sprayed turned out good but he forgot to cover the grip so that got some on it and dried now it is hard so try to cover tape
THAT WAS ME! |
|
| | |
Sponsored content
| | Subject: Re: Re-lacquering? | |
| |
|
| | |
|
